Fait fonctionner sur ardu micro

Makefile

@@ -46,7 +46,8 @@
 # $Id$
 
 #Bootloader Port
-PORT = /dev/serial/by-id/usb-Arduino__www.arduino.cc__Arduino_Mega_2560_6493534363335111A032-if00
+#PORT = /dev/serial/by-id/usb-Arduino__www.arduino.cc__Arduino_Mega_2560_6493534363335111A032-if00
+PORT = /dev/ttyACM0
 # /dev/serial/by-id/usb-Arduino_LLC_Arduino_Micro-if00
 #Device Port (for autoreset)
 RESETPORT = /dev/ttyU0
@@ -57,10 +58,10 @@ TARGET = pyrorf
 SRC = main.c lcd.c spi.c rf24.c
 CXXSRC =
 ASRC = i2cmaster.S
-MCU = atmega2560
+MCU = atmega32u4
 F_CPU = 16000000UL
 FORMAT = ihex
-UPLOAD_RATE = 20000
+UPLOAD_RATE = 57600
 
 # Name of this Makefile (used for "make depend").
 MAKEFILE = Makefile
@@ -98,10 +99,10 @@ LDFLAGS = -lm -Wl,--gc-sections
 
 
 # Programming support using avrdude. Settings and variables.
-AVRDUDE_PROGRAMMER = stk500
+AVRDUDE_PROGRAMMER = avr109
 AVRDUDE_PORT = $(PORT)
 AVRDUDE_WRITE_FLASH = -U flash:w:$(TARGET).hex:i
-AVRDUDE_FLAGS = -F -p m2560 -P$(AVRDUDE_PORT) -c $(AVRDUDE_PROGRAMMER) -b $(UPLOAD_RATE)
+AVRDUDE_FLAGS = -D -F -p m32u4 -P$(AVRDUDE_PORT) -c $(AVRDUDE_PROGRAMMER) -b $(UPLOAD_RATE)
 
 # Program settings
 CC = avr-gcc

i2cmaster.S

@@ -38,11 +38,23 @@
 
 ;******----- Adapt these SCA and SCL port and pin definition to your target !!
 ;
+#if defined (__AVR_ATmega32U4__)
+
+#define SDA             7          // SDA Port D, Pin 1   
+#define SCL             6           // SCL Port D, Pin 0
+#define SDA_PORT        PORTB       // SDA Port D
+#define SCL_PORT        PORTB       // SCL Port D         
+
+
+#else
+
 #define SDA             1          // SDA Port D, Pin 1   
 #define SCL             0           // SCL Port D, Pin 0
 #define SDA_PORT        PORTD       // SDA Port D
 #define SCL_PORT        PORTD       // SCL Port D         
 
+#endif
+
 ;******----------------------------------------------------------------------
 
 

lcd.c

@@ -32,6 +32,7 @@ void i2csend(uint8_t data){
 void pulseEnable (uint8_t data)
 {
    i2csend (data | _En);   // En HIGH
+ 
    i2csend (data);  // En LOW
 }
 

main.c

@@ -19,7 +19,7 @@ int main (void);
 void setup (void);
 void loop (void);
 void lcdprint( char* ptr);
-
+void debughex (uint8_t* ptr,uint8_t len);
 
 int main(void)
 {
@@ -30,32 +30,45 @@ int main(void)
 
 void setup(void)
 {
+#if defined(USBCON)
+	USBCON=0;
+#endif
+
 	lcd_init(20,4);
-	lcd_backlight(1);
+	lcd_backlight(0);
 	lcd_clear();
 	lcd_home();
+	lcd_display();
 	lcdprint("Pyro RF ! ");
-	
-	spi_init_master();
-	
-	rf24_init();
-	
-	char st = rf24_read_reg(CONFIG);
-	debughex(&st,1);
 
-#if defined(__AVR_ATmega32A__)
+	_delay_ms(200);
+
+	spi_init_master();
+	_delay_ms(200);
+	
+	rf24_setup();
+	
+//	rf24_init();
+	//char st = rf24_read_reg(STATUS);
+	rf24_update_fifo_status();
+	debughex(&rf24_status,1); 
+	
+	
+	
+	while(1);
+#if defined(TIMSK1)
 	// setup Timer1
 	TCCR1A = 0;
 	TCNT1=0;
-	OCR1A = 2000;
-	TIMSK = _BV(OCIE1A);
+	OCR1A = 10000;
+	TIMSK1 = _BV(OCIE1A);
 	TCCR1B = _BV(WGM12)|_BV(CS11);
 #elif defined(__AVR_ATmega2560__)
 	// setup Timer1
 	TCCR1A = 0;
 	TCNT1=0;
 	OCR1A = 10000;
-	TIMSK1 = _BV(OCIE1A);
+	TIMSK = _BV(OCIE1A);
 	TCCR1B = _BV(WGM12)|_BV(CS11);
 #endif	
 
@@ -90,7 +103,7 @@ void lcdprint( char* ptr)
 }
 
 
-void debughex (char* ptr,uint8_t len) {
+void debughex (uint8_t* ptr,uint8_t len) {
 	while (len--) {
 		uint8_t c = *(ptr++);
 	    uint8_t ch= c>>4;

rf24.c

@@ -24,6 +24,7 @@ void inline rf24_ceHi(){
 
 void inline rf24_ceLow(){
     CE_PIN_PORT &= ~_BV(CE_PIN_BIT);
+    
 }
 
 void inline rf24_csnHi(){
@@ -66,11 +67,15 @@ uint8_t rf24_read_reg(const uint8_t reg)
     return ret;
 }
 
+
+
 void rf24_update_fifo_status()
 {
 	rf24_csnLow();
+	_delay_ms(1);
 		rf24_status = spi_transfer(FIFO_STATUS);
 		rf24_fifo = spi_transfer(0);
+	_delay_ms(1);
 	rf24_csnHi();
 }
 
@@ -78,8 +83,9 @@ void rf24_setup()
 {
 	CE_PIN_DDR |= _BV(CE_PIN_BIT);
 	CSN_PIN_DDR |= _BV(CSN_PIN_BIT);
-	CE_PIN_PORT &= ~_BV(CE_PIN_BIT);
-	CSN_PIN_PORT |= _BV(CSN_PIN_BIT);
+	rf24_ceLow();
+	rf24_csnHi();
+	
 }
 
 void rf24_init()

rf24.h

@@ -13,7 +13,7 @@ void rf24_update_fifo_status();
 
 extern uint8_t rf24_status;
 extern uint8_t rf24_fifo;
-
+void rf24_setup();
 void rf24_init();
 
 /*
@@ -37,13 +37,13 @@ int rf24_waitforTX();
 
 #elif defined(__AVR_ATmega32U4__)
 
-#define CE_PIN_PORT PORTD
-#define CE_PIN_DDR DDRD
-#define CE_PIN_BIT PD4
+#define CE_PIN_PORT PORTB
+#define CE_PIN_DDR DDRB
+#define CE_PIN_BIT PB4
 
-#define CSN_PIN_PORT PORTC
-#define CSN_PIN_DDR DDRC
-#define CSN_PIN_BIT PC6
+#define CSN_PIN_PORT PORTB
+#define CSN_PIN_DDR DDRB
+#define CSN_PIN_BIT PB5
 
 #elif defined(__AVR_ATmega32A__)
 

spi.c

@@ -5,9 +5,9 @@
 void spi_init_master() {
 
     
-    SPI_PORT |= _BV(SCK_PIN);
+    SPI_PORT |= _BV(SCK_PIN)| _BV(SS_PIN);
     SPI_DDR |= _BV(MOSI_PIN) | _BV(SCK_PIN) | _BV(SS_PIN);
-    SPCR = _BV(SPE) | _BV(MSTR) | _BV(SPR1)| _BV(SPR0);
+    SPCR = _BV(SPE) | _BV(MSTR) ;
    
 }
 

spi.h

@@ -22,6 +22,18 @@ extern "C"{
 #define MOSI_PIN PB2
 #define MISO_PIN PB3
 
+#elif defined (__AVR_ATmega32U4__)
+
+#define SPI_PORT PORTB
+#define SPI_DDR DDRB
+
+
+#define SS_PIN PB0
+#define SCK_PIN PB1
+#define MOSI_PIN PB2
+#define MISO_PIN PB3
+
+
 #endif